ØUltra-low power design

ØSupports vibrating sensor

ØSupports Carlson, photoelectric level and LVDT displacement sensors

ØUp to 300 analog channels can be expanded

ØBuilt-in software without installation and can be used on Windows, Mac and Linux operating systems

ØThe instrument is set up through the web page

ØConnect to the instrument through network cable and USB data cable

ØIntuitive graphical interface

ØSimple setting interface for users of all levels

ØReal-time and historical data can be viewed

ØYou can display data with icons, bar charts, dials, and waveform charts

Application areas

Landslide treatment, dam wall monitoring, underground continuous wall monitoring, mining exploration, tunnel excavation, pile monitoring, etc.

System Introduction

Display and keys

Type: LCD display, 2 lines 16 characters, background light;

Display functions: channel data, alarm information, system status;

Key: View display information and operation functions through 6 keys;

Signal LED lights: 4 signal lights, indicating sampling, hard disk, alarm information and power supply respectively;

Software version upgrade

Software upgrades through RS232, network cable, USB cable or USB disk;

clock

Basic resolution: 200µs;

Accuracy: ±1 min per year (in an environment with a value of 40 ℃), ±4 min per year (in an environment with a value of -40 ℃ to 0 ℃, 40 ℃ to 70 ℃);

powered by

External power supply range: 10 to 30Vdc;

Built-in power supply: Not available;

Peak power: 12W (12Vdc 1A);

Average power loss

The relationship between sampling frequency and power consumption when using 12Vdc external power supply is as follows:

Basic Features

Digital shell: zinc-aluminum alloy;

Ruler    Inch: 180 x 137 x 65mm;

Weight   Quantity: 1.5kg;

Operating temperature: -40℃ to 70℃;

Operating humidity:<85%, water vapor does not condense;

Note: Low and high temperature environments will reduce battery life.LCDThe operating temperature of the display is-15℃ to50℃.

Simulation channel

The DT80G has 5 analog channels, which can be expanded to up to 100 analog channels. Each analog channel can be connected to a three-wire or four-wire input, two independent two-wire inputs, and three two-wire single-ended inputs.

The specific number of accesses is as follows:

Two-wire single-ended channels: 15 (up to 300 expansion);

Two-wire differential channels: 10 (up to 200 expansion);

Three-wire or four-wire differential channels: 5 (up to 100 expansion);

Note: Extensions require configurationC em20Module, a module contains20analog channels.

Basic input range

The basic input voltage, current, resistance and frequency range that the DT80G can measure is as follows:

The basic input voltage, current, resistance and frequency accuracy that the DT80G can measure is as follows:

Note: Accuracy is relative to full scale.

Sampling information

For measurement accuracy and suppression of the effects of noise, a row frequency period greater than 50/60Hz is integrated.

Maximum sampling speed: 25Hz;

Effective resolution: 18 bits;

Linearity: 0.01%;

Common mode suppression: >90dB;

WireSexual chain mode suppression: >35dB.

enter

Channel isolation: 100V (relay on);

Isolation of analog components: 100V (optical isolation);

Input impedance: 100KΩ, >100MΩ;

Common mode range: ±3.5V, or ±35V in the 30V range.

Sensor excitation

Analog channel excitation: 250µA or 2.5mA precision current source, 4.5V voltage, can switch external power supply;

General Excitation: Can turn on and close 12V power supply (maximum 150mA) to power sensors and accessories, and can turn on and close 5V power supply (maximum 25mA) to power analog channels.

Analog sensors

Several common sensors are introduced, but the sensors that the DT80G can connect to are not limited to the following types.

Thermocouple

Thermocouple types: B, C, D, E, G, J, K, N, R, S, T-type;

Thermocouple calibration: ITS-90;

RT DS

RTDs material types: Pt, Ni, Cu;

Resistance range: 10Ω to 10KΩ;

Vibrating string

Frequency range: 500 to 5KHz;

Coil resistance: 50 to 200Ω;

Simulation method: single pulse pluck;

Thermistor

Thermistor type: YSI400xx series;

Resistance range: <10kΩ

Note 1: Other thermistor types are also supported.

Note 2: The measurement range can be expanded by parallel resistance.

Single-chip temperature sensor

Support types: LM34-60, AD590\592, TMPxx, LM135, 235, 335;

Strainer and bridge sensor

Configuration: 1/4 bridge, 1/2 bridge and full bridge;

Excitation: voltage or current;

Carlsonsensor

Inline stress and temperature functions;

4-20MACurrent ring

Digital Channel

Digital input/Output

8 two-way channels

Input type: 8 logic levels (maximum 20/30V);

Output type: 4 field effect transistors (maximum: 30V, 100mA), 4 logic outputs;

Relay output

1 direct-connected self-locking relay (maximum: 30Vdc, 1A).

Low speed counting

8-channel counter, shared with digital channels; low-speed counting function does not work in sleep mode.

Model: 32bit;

Maximum counting rate: 10Hz;

Special counting input

4 high speed or 2 phase encoder inputs

Model: 32bit;

Maximum counting rate: 100kHz;

Serial Channel

SDI-12

There are four SDI-12 channels shared with digital channels, and each SDI-12 channel can be connected to many SDI-12 sensors;

Universal serial sensor

It can easily record data in sensors and data streams.

Available ports: serial sensor port (RS232, RS422, RS485) or host RS232 port;

Baud rate: 300 to 115200.

Note: When using the serial sensor channel, the host port is not available for communication.

Compute channel

Call the police

Conditions: below, above, within or outside the range;

Delay: optional alarm response time;

Action: Digital output, pass information or execute any datataker command.

Data collection list

Schedule sampling interval: Each schedule has a separate sampling interval, which can be selected from 10ms to days.

Data storage

Built-in storage

Storage space: 128MB, about 10,000,000 data can be stored (large space memory can be customized);

External storage device(Optional)

USB1.1, USB2.0 and other USB flash memory devices.

Communication panel

Network cable port

Panel: 10Mbps;

Protocol: TCP/IP, Modbus protocol;

USBport

Panel: USB1.1 (virtual communication interface);

Protocol: ASCII command;

HostRS232port

Speed: 300 to 115200 baud rate (default 57600);

Flow control: Hardware (RTS/CTS);

Software (XON/XOFF): None

Handshake protocol: DCD, DSR, DTR, RTS, CTS;

Modem supports: automatic answering and dialing;

Protocol: ASCII command, TCP/IP (PPP), Modbus protocol, serial sensor;

Serial sensor port

Panels: RS232, RS422m, RS485;

Speed: 300 to 57600 baud rate;

Flow control: Hardware (RTS/CTS);

Software (XON/XOFF): None

Handshake protocol: DCD, DSR, DTR, RTS, CTS;

Network Services (TCP/IP)

Use network cable port or host RS232 port

Command panel: Enter the ASCII command panel of DT80G through TCP/IP;

Network server: access the status of existing data and data acquisition through web pages, set the user's characteristic display interface, and download CSV format data;

Modbus server (controlled end): obtain data and data acquisition status through the Modbus client;

Modbus client (main control): read data from the modbus device or write data to the modbus device;

FTP server: Obtain stored data through a browser or FTP client;